easy connect LED120Dif-lighting strip

    Switch GmbH & Co. KG has extended the product range in the area of LED-lighting strips. The new easy connect LED120Dif-lighting strip is based on the well proven easy connect LED120-lighting strip but with a semi-dulled jacket material.

      The advantages at a glance:

    • Large number of LEDs enables a wide radiation
    • → higher illumination in the shaft
      → all-over illumination of the shaft without horizontal shadows

    • Large number of LEDs per meter
    • → reduces direct dazzling

    • Semi dulled jacket material
    • → reduces considerably direct dazzling
      → less reduction in illumination

    • The printed circuit board is RoHS compliant
    • → easy to be recycled

    • Deployment of ultra high performance LEDs
    • → highest degree of illumination
      → minimum power consumption

    • Reduced generation of heat and larger cooling surface per LED
    • → increases service life
      → applicable for long-term usage

    • Neutral colour of the LEDs
    • → natural colour rendering of all components in the shaft

    • Robust construction and reinforced jacket
    • → prevents damages due to improper handling

    • LED-connection box with semiconductor protection
    • → protects the rectifier against stress peaks in the main power supply

    • LED-connection box with fuse
    • → protects the feed-line of the LED-light strip

      You will find detailed Information with regrad to our new development here.

easy connect LED120-lighting strip, the result of continuous improvements

      The advantages of continuous further developments at a glance:

    • Large number of LEDs enables a wide radiation
    • → higher illumination in the shaft
      → all-over illumination of the shaft without horizontal shadows

    • Large number of LEDs per meter
    • → reduces direct dazzling

    • The printed circuit board is RoHS compliant
    • → easy to be recycled

    • Deployment of ultra high performance LEDs
    • → highest degree of illumination
      → minimum power consumption

    • Reduced generation of heat and larger cooling surface per LED
    • → increases service life
      → applicable for long-term usage

    • Neutral colour of the LEDs
    • → natural colour rendering of all components in the shaft

    • Robust construction and reinforced jacket
    • → prevents damages due to improper handling

    • LED-connection box with semiconductor protection
    • → protects the rectifier against stress peaks in the main power supply

    • LED-connection box with fuse
    • → protects the feed-line of the LED-light strip

      You will find detailed Information with regrad to our new development here.

Emergency push button and flashing buzzer in a compact box

 

Switch GmbH & Co. KG has developed another suitable product to comply with the European safety standard EN 81.20.
The standard requires an electrical bypass at the shaft- and cabin-doors as well as at the door latching devices for maintenance. The activation of this bypass is based on various conditions. One requirement is an audible signal in the cabin and a flashing light below the cabin, which are in operation during the drive. The sound level has to be 55 dBA minimum at 1 m distance.

Switch GmbH and Co. & KG provides an appropriate solution to achieve this mandatory requirement. A powerful buzzer generates a warning signal of more than 80 dBA in 1 meter distance. The frequency of this alert is approx. 1000 Hz. In addition a flashing red light facilitates the visual alarm. Both warnings alternate with a frequency of 0.5 Hz.
An emergency bush button is implemented in the small box to increase the safety aspect. The service technician can easily contact the emergency head office.
Please contact the Switch experts for further information and technical data. They are pleased to support your request.

easy connect LED-lighting strips with connection technology up to protection class IP68

 

Switch GmbH & Co. KG has improved the well-tried easy connect LED-lighting strips.

The LED-lighting strips are equipped with a new connection technology according to market requirements. This measure provides an optimised connection of the LED-lighting strips to the power supply. The former integrated rectifier is replaced by a component in a separate housing. Of course the box with the cable glands meets the protection class IP65. A 10 m power supply cord with a shaped-plug is connected to the box in standard configuration. The box has two fastening lugs for easy installation.

The advantage of this new layout is the flexibility in wiring configuration. It is self-evident that the new layout offers the well known Switch easy connect philosophy: Fix the LED-lighting strip, plug in the shaped-plug, light in the whole shaft already during installation phase.
After finishing the installation the LED-lighting strip can be connected to the existing control unit. In this coherence the rectifier can be built into the control unit too.

The new flexible design enables the assembly of easy connect LED-lighting strips achieving the high protection class IP68. Please contact Switch experts for further information.

easy connect LEDplus for the cabin roof

Switch GmbH & Co. KG is proud to offer short LED-lightbands with emergency light function which can be installed very easily on top of a cabin or in the pit. These solutions are based on the well known LED-technology of the Switch shaft lighting.

It is self-evident that all requirements of the new European regulation EN 81-20 are met.

The LED-lightbands offer the well-tried 2 in 1-technique:

A regular lighting with 230 VAC power supply and an emergency lighting with a 12 or 24 VDC power supply.

In this case an available emergency power supply of the cabin light can be used due to the low power consumption of the LED-strip.

The easy connect LEDplus system can be installed quite fast and easily providing a high degree of free moving capacity to the service technician; no cables on the cabin roof, no dangerous tripping points. Both hands are free for the necessary maintenance.

The easy connect LED-Lightbands are delivered ready for connection with a small plastic box.

Optionally pre-assembled Molex-connectors can be provided.

Technical dataEC3_230/12-1EC3_230/24-1
Power supply / main lighting230 - 240 VAC230 - 240 VAC
Power supply / emergency lighting12 VDC24 VDC
Length of LED-strip1 Meter1 Meter
Length of LED connecting cable0.4 Meter0.4 Meter
Burning characteristicself extinguishingself extinguishing
Power consumption emergency lighting80 mA30 mA
Lifetime (mttf) approx.50,000 hours50,000 hours
Material connection boxPolystyrenePolystyrene
Dimensions (L x W x H)88 x 88 x 53 mm88 x 88 x 53 mm
Degree of protectionIP65IP65
Temperature range-20°C up to +60°C-20°C up to +60°C

easy connect LEDplus with control unit

Switch GmbH & Co. KG is proud to offer now the complete system exceeding the new European safety Regulation EN81-20 5.4.10.4c. In addtion to the easy connect LEDplus shaft lighting a control unit is now available.

The unit provides the power for emergency light as well as the necessary electronic system suitable for the LED shaft lighting with emergency light function. The unit monitors continuously the main power supply and will switch immediately to the emergency light in case of a breakdown of the main power.
The box includes the rechargeable batteries and the charging unit for the low voltage circuit.

The maximum operating time of the emergency light is depending on the height of the shaft respectively the length of the LED-strip.

Switch GmbH & Co. KG offers two variants depending on the area of operation and the required capacity of the rechargeable batteries. It is self-evident that both versions meet the requirements of the European regulation:

1. Heavy duty  version
produkt_01
In general this Switch emergency light power supply provides an emergency light up to 3 hours. It meets the strong British building standards in addition to the safety regulation EN81-20.
The electronic system is built in a powdercoated metal box. The box is equipped with a solid interlock. The necessary key is part of the delivery.
A voltage warning sticker is glued to the cover.
A test button is embedded in the cover. It allows to test the correct operation of the emergency light.

2. SlimLine version
produkt_01
This Switch complete solution offers an emergency light of more than one hour and thereby exceeding the European safety regulation. The electronic is placed in a solid plastic box, which meets the protection class IP66.

Technical data 
Input power230 - 240 VAC
Output power / main power supply230 - 240 VDC
Output power / emergency light24 VDC
Average duration of emergency light> 3 hours
Power consumption emergency LED light strip0.6 W/m, max. 25 W/50 m
Material of the boxPolysterene
Housing protection classIP66
Temperature range-20°C up to +50°C
Dimensions (Width x Height x Depth)255 x 180 x 110 mm
Weightapprox. 4.1 kg
Fuse for plug socket of pit bottom box10 A

The Switch electronic system can be placed in the engine room, on top of the cabin or in the shaft.

Please contact Switch GmbH & Co. KG for further information and technical data.